Audiowerk Installation Notes

 

1. System Requirements. 1

2. Initial Installation. 1

2.1. Initial Installation on Windows 9x systems (here: Windows Millennium Edition) 1

2.2. Initial Installation under Windows 2000. 2

3. Driver Update. 2

3.1. Driver Update on Windows 9x systems (here: Windows Millennium Edition) 2

3.2. Driver Update under Windows 2000. 3

 

 

1. System Requirements

 

(* For Windows NT 4.0 you will need a separate setup package)

 

This driver package will install the following drivers:

 

 

The latest driver package is always available via the Internet at: http://www.emagic.de/.

 

 

2. Initial Installation

 

This section describes the installation procedure of the Audiowerk for the first time on your computer. If a driver for the Audiowerk is already installed on your system you should refer to the Driver Update section. The following subsections provide a step-by-step guide to the initial installation of the Audiowerk drivers under Windows 9x systems, and Windows 2000.

2.1. Initial Installation on Windows 9x systems (here: Windows Millennium Edition)

 

§         Switch off your computer and remove the power plug.

§         Plug the Audiowerk card into a free PCI slot of your computer. Please follow very carefully the instructions from your manual.

§         Switch on your computer.

§         After Windows has been booted the "Add New Hardware" Wizard will automatically launch.

§         If you are installing the drivers from CD-ROM, insert the Audiowerk drivers CD-ROM into your computer's CD-ROM drive.

§         Select the following option: “Automatic search for a better driver (Recommended)”.

§         Click on the "Next" button.

§         After a few seconds, the following message will appear: “Windows has finished installing the new hardware device.”

§         Click on the "Finish" button.

§         This will launch the following dialog: “To finish setting up your new hardware, you must restart your computer.” Click on the “Yes” button.

§         Your computer will restart.

§         Your installation will have been completed successfully

 

2.2. Initial Installation under Windows 2000

 

§         The "Add New Hardware" Wizard will automatically launch.

§         If you are installing the drivers from CD-ROM, insert the Audiowerk drivers CD-ROM into your computer's CD-ROM drive.

§         Click on the "Next" button.

§         Select "Search for a suitable driver for my device (recommended)

§         Click on the "Next" button.

§         Select a search location, if necessary. If you are installing the driver from CD-ROM, check the CD-ROM drive option.

§         Click on the "Next" button.

§         The following message will appear on-screen: “The wizard found a driver for the following device: Multimedia controller"

§         Click on the "Next" button.

§         This will be followed by the "Digital Signature Not Found" message.

§         This message is shown as the Emagic Audiowerk drivers currently do not contain a Microsoft digital signature. It is safe to install the drivers. The Emagic drivers are fully functional and there is no risk attached to the installation of these drivers on your system.

§         You will be asked the following: "Do you want to continue the installation?"

§         Click on the "Yes" button.

§         The: "Completing the Found New Hardware Wizard, Emagic Audiowerk2, Audiowerk8, Windows has finished installing the software for this device. The hardware you installed will not work until you restart your computer" message will appear.

§         Click the "Finish" button.

§         You will be prompted with the following dialog: "You must restart your computer before the new settings will take effect."

§         Click on the "Yes" button.

§         Your computer will restart.

§         Following these steps, your installation will have been completed successfully.

 

 

3. Driver Update

    

This section describes the update procedure for a system with an existing Audiowerk driver installed. If this is the first time you have plugged the Audiowerk card into your computer, you should refer to the Initial Installation section. The following subsections detail the steps necessary to update the Audiowerk drivers under Windows 9x systems, and Windows 2000.

3.1. Driver Update on Windows 9x systems (here: Windows Millennium Edition)

 

 

3.2. Driver Update under Windows 2000

 

§         This will be followed by the "Digital Signature Not Found" message.

§         This message is shown as the Emagic Audiowerk drivers currently do not contain a Microsoft digital signature. It is safe to install the drivers. The Emagic drivers are fully functional and there is no risk attached to the installation of these drivers on your system.

§         You will be asked the following: "Do you want to continue the installation?"

§         Click on the "Yes" button.